Homemade Two types of cunt spreader

Doctor Pervert

Retired
  • Straight
  • Male
  • Private
May 19, 2013
3,508
4,731
483
I have been meaning to get these little home made items up for a while and at the recent prompting of a member I am finally getting around to it!

So for these you will need one regular wire coat hanger, those flimsy ones from the dry cleaner are ideal. You will also need a set of linesmans pliers, mine as you can see in the photos are well worn. If you don't have any it's worth buying some just for this. You use these to both cut and bend the hanger into the required shapes.

spreader 01.jpg

Start by cutting one arm off the hanger using the cutter section of your pliers.
spreader 02.jpg

Then bend the cut section to match the spreader in the photo.
spreader 03.jpg

Cut off the second arm,
spreader 04.jpg

Then bend this section to match the second spreader in this photo.
spreader 05.jpg

You now have two devices.
The first one is designed to be used sideways, legs spread and the hooks held back with straps or tape around your upper thighs.
The second one runs front to back and the hooks this time attach to either rubber bands or cord that run to a belt worn around the waist.

Just one word of warning, be careful of the cut ends as they are left quite sharp by the cutting, you can file them smooth or cap them with a few wraps of electrical insulation tape.

Enjoy!
 

Doctor Pervert

Retired
  • Straight
  • Male
  • Private
May 19, 2013
3,508
4,731
483
details, part 1

I've had a user request for details on how this is done, so here is the step by step guide to making both from one coat hanger!

Now before you begin note that this is not an exact thing, close enough is definitely good enough here and any dimensions are just a guide to help you out.

So start with a plain wire coat hanger and measure about 18cm (7") along each side from the ends.
IMG_1748.jpg

Now use the side cutters in your pliers to cut at the marks.
IMG_1749.jpg

Mark the mid points on each side of the cut sections.
IMG_1750.jpg

And add a couple of guide marks the width of your pliers, remember this is just a guide not precise.
IMG_1751.jpg

Now bend both legs at the centre mark inwards.
IMG_1752.jpg
 

Doctor Pervert

Retired
  • Straight
  • Male
  • Private
May 19, 2013
3,508
4,731
483
details, part 2

The legs will cross over like this.
IMG_1753.jpg

Now bend the legs back the other way to make this "U" shape in the sides.
IMG_1754.jpg

You should now have something that looks like this, both types of spreader are the same to this point so you can copy the steps so you have 2 like this.
IMG_1755.jpg
 

Doctor Pervert

Retired
  • Straight
  • Male
  • Private
May 19, 2013
3,508
4,731
483
details, part 3

On one frame grip the ends and fold back to make the tie loops.
IMG_1756.jpg

Like this.
IMG_1757.jpg

Now take the second frame.
IMG_1758.jpg

And this time straighten the legs by gripping inside the "U" and bending up.
IMG_1759.jpg

Finally, bend the attachment loops folding them inside as shown.
IMG_1760.jpg

And you are done!
 

Doctor Pervert

Retired
  • Straight
  • Male
  • Private
May 19, 2013
3,508
4,731
483
A handy member has made these up, as you can see in the photo she sent it is possible to use both at the same time!

2018-11-21 (1).jpg
 
  • Like
Reactions: Sk33t3r

Featured Threads

New Personals